 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Obsolete Device TC1025 Linear Building Block - Dual Low Power Comparator Features * Rail-to-Rail Inputs and Outputs * Optimized for Single Supply Operation * Small Packages: 8-Pin MSOP, 8-Pin SOIC or 8-Pin PDIP * Ultra Low Input Bias Current: Less than 100pA * Low Quiescent Current: 8A (Typ.) * Operates Down to VDD = 1.8V General Description The TC1025 is a dual low-power comparator with a typical supply current of 8A and operation ensured to VDD = 1.8V. Input and output signal swing is rail-to-rail. Available in a space-saving 8-pin MSOP package, the TC1025 consumes half the board area required by a standard 8-Pin SOIC package. It is also available in 8-Pin SOIC and PDIP packages. It is ideal for applications requiring high integration, small-size and low power. Applications * Power Management Circuits * Battery Operated Equipment * Consumer Products Functional Block Diagram OUTA 1 TC1025 8 OUTB Device Selection Table Part Number TC1025CEPA TC1025CEUA TC1025CEOA Package 8-Pin PDIP 8-Pin MSOP 8-Pin SOIC Temperature Range -40C to +85C -40C to +85C -40C to +85C INA4 5 VSS 2 A - - B 7 VDD + INA+ 3 + 6 INB+ INB- Package Types 8-Pin PDIP 8-Pin MSOP 8-Pin SOIC OUTA VSS INA+ INA1 2 3 4 8 7 OUTB VDD INB+ INB- TC1025CEPA TC1025CEUA TC1025CEOA 6 5 (c) 2005 Microchip Technology Inc. DS21656C-page 1 TC1025 1.0 ELECTRICAL CHARACTERISTICS *Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. ABSOLUTE MAXIMUM RATINGS* Supply Voltage ......................................................6.0V Voltage on Any Pin .......... (VSS - 0.3V) to (VDD + 0.3V) Junction Temperature....................................... +150C Operating Temperature Range.............-40C to +85C Storage Temperature Range ..............-55C to +150C TC1025 ELECTRICAL SPECIFICATIONS Electrical Characteristics: Typical values apply at 25C and VDD = 3.0V. Minimum and maximum values apply for TA = -40 to +85C, and VDD = 1.8V to 5.5V, unless otherwise specified. Symbol VDD IQ VICMR VOS IB VOH VOL CMRR PSRR ISRC Parameter Supply Voltage Supply Current Common Mode Input Range Input Offset Voltage Input Bias Current Output High Voltage Output Low Voltage Common Mode Rejection Ratio Power Supply Rejection Ratio Output Source Current Min 1.8 -- VSS - 0.2 -5 -5 -100 VDD - 0.3 -- 66 60 1 Typ -- 8 -- -- -- -- -- -- -- -- Max 5.5 12 VDD + 0.2 +5 +5 100 -- 0.3 -- -- -- Units V A V mV mV pA V V dB dB mA VDD = 3V, VCM = 1.5V, TA = 25C TA = 25C, IN+,IN- = VDD to VSS RL = 10k to VSS RL = 10k to VDD TA = 25C, VDD = 5V VCM = VDD to VSS TA = 25C, VCM = 1.2V VDD = 1.8V to 5V IN+ = VDD, IN- = VSS, Output Shorted to VSS VDD = 1.8V IN+ = VSS, IN- = VDD, Output Shorted to VDD VDD = 1.8V 100mV Overdrive, CL = 100pF 10mV Overdrive, CL = 100pF Test Conditions Comparator ISINK Output Sink Current 2 -- -- mA tPD1 tPD2 Response Time Response Time -- -- 4 6 -- -- sec sec DS21656C-page 2 (c) 2005 Microchip Technology Inc. TC1025 2.0 PIN DESCRIPTION The description of the pins are listed in Table 2-1. TABLE 2-1: Pin No. (8-Pin PDIP) (8-Pin MSOP) (8-Pin SOIC) 1 2 3 4 5 6 7 8 PIN FUNCTION TABLE Symbol Description OUTA VSS INA+ INAINBINB+ VDD OUTB Comparator output. Negative power supply. Non inverting input. Inverting input. Inverting input. Non inverting input. Positive power supply. Comparator input. (c) 2005 Microchip Technology Inc. DS21656C-page 3 TC1025 3.0 DETAILED DESCRIPTION 4.0 TYPICAL APPLICATIONS The TC1025 is one of a series of very low-power, linear building block products targeted at low-voltage, singlesupply applications. The TC1025 minimum operating voltage is 1.8V, and typical supply current is only 8A. It combines two comparators in a single package. The TC1025 lends itself to a wide variety of applications, particularly in battery-powered systems. Typically, it finds application in power management, processor supervisory, and interface circuitry. 4.1 3.1 Comparators The TC1025 contains two comparators. The comparator's input range extends beyond both supply voltages by 200mV and the outputs will swing to within several millivolts of the supplies depending on the load current being driven. The comparators exhibit propagation delay and supply current which are largely independent of supply voltage. The low input bias current and offset voltage make them suitable for high impedance precision applications. 2. 3. External Hysteresis (Comparator) Hysteresis can be set externally with two resistors using positive feedback techniques (see Figure 4-1). The design procedure for setting external comparator hysteresis is as follows: 1. Choose the feedback resistor RC. Since the input bias current of the comparator is at most 100pA, the current through RC can be set to 100nA (i.e., 1000 times the input bias current) and retain excellent accuracy. The current through RC at the comparator's trip point is VR/ RC where VR is a stable reference voltage. Determine the hysteresis voltage (VHY) between the upper and lower thresholds. Calculate RA as follows: EQUATION 4-1: VHY R A = R C ---------- V DD 4. 5. Choose the rising threshold voltage for VSRC (VTHR). Calculate RB as follows: EQUATION 4-2: 1 R B = ---------------------------------------------------------VTHR 1 1 -------------------- - ------ - ------ VR x RA RA RC 6. Verify the formulas: VSRC rising: threshold voltages with these EQUATION 4-3: 1 1 1 VTHR = ( V R ) ( R A ) ------ + ------ + ------- R A R B R C VSRC falling: EQUATION 4-4: R A x VDD V THF = V THR - ------------------------ RC DS21656C-page 4 (c) 2005 Microchip Technology Inc. TC1025 4.2 32.768 kHz "Time of Day Clock" Crystal Controlled Oscillator 4.4 Oscillators and Pulse Width Modulators A very stable oscillator driver can be designed by using a crystal resonator as the feedback element. Figure 4-2 shows a typical application circuit using this technique to develop clock driver for a Time Of Day (TOD) clock chip. The value of RA and RB determine the DC voltage level at which the comparator trips - in this case onehalf of VDD. The RC time constant of RC and CA should be set several times greater than the crystal oscillator's period, which will ensure a 50% duty cycle by maintaining a DC voltage at the inverting comparator input equal to the absolute average age of the output signal. 4.3 Non-Retriggerable One Shot Multivibrator Using two comparators, a non-retriggerable one shot multivibrator can be designed using the circuit configuration of Figure 4-3. A key feature of this design is that the pulse width is independent of the magnitude of the supply voltage because the charging voltage and the intercept voltage are a fixed percentage of VDD. In addition, this one shot is capable of pulse width with as much as a 99% duty cycle and exhibits input lockout to ensure that the circuit will not retrigger before the output pulse has completely timed out. The trigger level is the voltage required at the input to raise the voltage at node A higher than the voltage at node B, and is set by the resistive divider R4 and R10 and the impedance network composed of R1, R2 and R3. When the one shot has been triggered, the output of CMPTR2 is high, causing the reference voltage at the non-inverting input of CMPTR1 to go to VDD. This prevents any additional input pulses from disturbing the circuit until the output pulse has timed out. The value of the timing capacitor C1 must be small enough to allow CMPTR1 to discharge C1 to a diode voltage before the feedback signal from CMPTR2 (through R10) switches CMPTR1 to its high state and allows C1 to start an exponential charge through R5. Proper circuit action depends upon rapidly discharging C1 through the voltage set by R6, R9 and D2 to a final voltage of a small diode drop. Two propagation delays after the voltage on C1 drops below the level on the non-inverting input of CMPTR2, the output of CMPTR1 switches to the positive rail and begins to charge C1 through R5. The time delay which sets the output pulse width results from C1 charging to the reference voltage set by R6, R9 and D2, plus four comparator propagation delays. When the voltage across C1 charges beyond the reference, the output pulse returns to ground and the input is again ready to accept a trigger signal. Microchip's linear building block comparators adapt well to oscillator applications for low frequencies (less than 100kHz). Figure 4-4 shows a symmetrical square wave generator using a minimum number of components. The output is set by the RC time constant of R4 and C1, and the total hysteresis of the loop is set by R1, R2 and R3. The maximum frequency of the oscillator is limited only by the large signal propagation delay of the comparator in addition to any capacitive loading at the output which degrades the slew rate. To analyze this circuit, assume that the output is initially high. For this to occur, the voltage at the inverting input must be less than the voltage at the non-inverting input. Therefore, capacitor C1 is discharged. The voltage at the non-inverting input (VH) is: EQUATION 4-5: R2 ( VDD ) V H = -------------------------------------------[ R2 + ( R1 || R3 ) ] where, if R1 = R2 = R3, then: EQUATION 4-6: 2 ( V DD ) V H = ------------------3 Capacitor C1 will charge up through R4. When the voltage at the comparator's inverting input is equal to VH, the comparator output will switch. With the output at ground potential, the value at the non-inverting input terminal (VL) is reduced by the hysteresis network to a value given by: EQUATION 4-7: V DD V L = ---------3 Using the same resistors as before, capacitor C1 must now discharge through R4 toward ground. The output will return to a high state when the voltage across the capacitor has discharged to a value equal to VL. The period of oscillation will be twice the time it takes for the RC circuit to charge up to one half its final value. The period can be calculated from: EQUATION 4-8: 1 ---------------- = 2 ( 0.694 ) ( R4 ) ( C1 ) FREQ (c) 2005 Microchip Technology Inc. DS21656C-page 5 TC1025 The frequency stability of this circuit should only be a function of the external component tolerances. Figure 4-5 shows the circuit for a pulse width modulator circuit. It is essentially the same as in Figure 4-4, but with the addition of an input control voltage. When the input control voltage is equal to one-half VDD, operation is basically the same as described for the free-running oscillator. If the input control voltage is moved above or below one-half VDD, the duty cycle of the output square wave will be altered. This is because the addition of the control voltage at the input has now altered the trip points. The equations for these trip points are shown in Figure 4-5 (see VH and VL). Pulse width sensitivity to the input voltage variations can be increased by reducing the value of R6 from 10k and conversely, sensitivity will be reduced by increasing the value of R6. The values of R1 and C1 can be varied to produce the desired center frequency. FIGURE 4-1: COMPARATOR EXTERNAL HYSTERESIS CONFIGURATION RC TC1025 RA VSRC VDD + - VOUT 1/2 RB VR FIGURE 4-2: 32.768 kHz "TIME OF DAY" CLOCK OSCILLATOR 32.768kHz VDD RA 150k VDD 1/2 + _ TC1025 VOUT RC RB 150k CA 100pF 1M Vper = 30.52sec FIGURE 4-3: NON-RETRIGGERABLE MULTIVIBRATOR VDD TC1025 IN R3 1M R1 R4 1M A - CMPTR1 R5 10M R6 562k C C1 100pF TC1025 - CMPTR2 R7 1M OUT OUT VDD GND 100k R2 100k IN t0 GND B + D1 R10 61.9k + R8 C VDD GND R9 243k 10M D2 DS21656C-page 6 (c) 2005 Microchip Technology Inc. TC1025 FIGURE 4-4: SQUARE WAVE GENERATOR VDD R1 100k TC1025 R4 VDD - 1/2 TC1025 VH = VL = R2 (VDD) R2 + (R1||R3) C1 + R2 100k R3 100k (VDD) (R2||R3) R1 + (R2||R3) 1 FREQ = 2(0.694)(R4)(C1) FIGURE 4-5: PULSE WIDTH MODULATOR VDD R1 100k VC TC1025 R4 1/2 TC1025 VDD - VL = VDD (R2R3R6) + VC (R1R2R3) R1R2R6 + R1R3R6 + R2R3R6 + R1R2R3 1 2 (0.694) (R4) (C1) VH = VDD (R1R2R6 + R2R3R6) + VC (R1R2R3) R1R2R6 + R1R3R6 + R2R3R6 + R1R2R3 R6 10k C1 + FREQ = For Square Wave Generation Select R1 = R2 = R3 R3 100k VC = VDD 2 R2 100k (c) 2005 Microchip Technology Inc. DS21656C-page 7 TC1025 5.0 Note: TYPICAL CHARACTERISTICS The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. Comparator Propagation Delay vs. Supply Voltage 7 DELAY TO RISING EDGE (sec) DELAY TO FALLING EDGE (sec) Comparator Propagation Delay vs. Supply Voltage 7 6 DELAY TO RISING EDGE (sec) Comparator Propagation Delay vs. Temperature 7 Overdrive = 100mV 6 TA = 25C CL = 100pF TA = 25C CL = 100pF 6 Overdrive = 10mV Overdrive = 10mV 5 4 5 4 Overdrive = 100mV Overdrive = 50mV 5 VDD = 5V VDD = 4V 3 2 1.5 2 2.5 3 Overdrive = 50mV 3 2 4 VDD = 2V VDD = 3V 3 1.5 2 2.5 3 3.5 4 4.5 5 5.5 -40C 25C SUPPLY VOLTAGE (V) 3.5 4 4.5 5 5.5 85C SUPPLY VOLTAGE (V) TEMPERATURE (C) Comparator Propagation Delay vs. Temperature 7 DELAY TO FALLING EDGE (sec) Overdrive = 100mV 6 VDD - VOUT (V) VDD = 5V Comparator Output Swing vs. Output Source Current 2.5 2.0 VDD = 3V VDD = 1.8V TA = 25C Comparator Output Swing vs. Output Sink Current 2.5 2.0 VOUT - VSS (V) TA = 25C 5 VDD = 4V VDD = 3V VDD = 2V 1.5 1.0 1.5 1.0 VDD = 3V VDD = 1.8V VDD = 5.5V 4 .5 0 25C TEMPERATURE (C) 85C 0 1 VDD = 5.5V .5 0 3 -40C 3 2 4 ISOURCE (mA) 5 6 0 1 2 3 4 5 6 ISINK (mA) Comparator Output Short-Circuit Current vs. Supply Voltage OUTPUT SHORT-CIRCUIT CURRENT (mA) 60 TA = -40C TA = 25C TA = 85C 30 20 Sinking 10 Sourcing 0 0 Supply Current vs. Supply Voltage 10 SUPPLY CURRENT (A) 50 40 9 8 7 TA = 25C 6 5 4 TA = 85C TA = -40C TA = -4 C 0 TA = 25C TA = 85C 6 3 1 2 4 5 SUPPLY VOLTAGE (V) 0 1 3 2 4 5 SUPPLY VOLTAGE (V) 6 DS21656C-page 8 (c) 2005 Microchip Technology Inc. TC1025 6.0 6.1 PACKAGING INFORMATION Package Marking Information Package marking data not available at this time. 6.2 Taping Form Component Taping Orientation for 8-Pin MSOP Devices User Direction of Feed PIN 1 W P Standard Reel Component Orientation for TR Suffix Device Carrier Tape, Number of Components Per Reel and Reel Size Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size 8-Pin MSOP 12 mm 8 mm 2500 13 in Component Taping Orientation for 8-Pin SOIC (Narrow) Devices User Direction of Feed PIN 1 W P Standard Reel Component Orientation for TR Suffix Device Carrier Tape, Number of Components Per Reel and Reel Size Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size 8-Pin SOIC (N) 12 mm 8 mm 2500 13 in (c) 2005 Microchip Technology Inc. DS21656C-page 9 TC1025 6.3 Package Dimensions 8-Pin Plastic DIP PIN 1 .260 (6.60) .240 (6.10) .045 (1.14) .030 (0.76) .400 (10.16) .348 (8.84) .200 (5.08) .140 (3.56) .150 (3.81) .115 (2.92) .070 (1.78) .040 (1.02) .310 (7.87) .290 (7.37) .040 (1.02) .020 (0.51) .015 (0.38) .008 (0.20) .400 (10.16) .310 (7.87) 3 MIN. .110 (2.79) .090 (2.29) .022 (0.56) .015 (0.38) Dimensions: inches (mm) 8-Pin MSOP PIN 1 .122 (3.10) .114 (2.90) .197 (5.00) .189 (4.80) .026 (0.65) TYP. .122 (3.10) .114 (2.90) .043 (1.10) MAX. .016 (0.40) .010 (0.25) .006 (0.15) .002 (0.05) 6 MAX. .028 (0.70) .016 (0.40) .008 (0.20) .005 (0.13) Dimensions: inches (mm) DS21656C-page 10 (c) 2005 Microchip Technology Inc. TC1025 6.3 Package Dimensions (Continued) 8-Pin SOIC PIN 1 .157 (3.99) .150 (3.81) .244 (6.20) .228 (5.79) .050 (1.27) TYP. .197 (5.00) .189 (4.80) .069 (1.75) .053 (1.35) .020 (0.51) .010 (0.25) .013 (0.33) .004 (0.10) .010 (0.25) .007 (0.18) .050 (1.27) .016 (0.40) Dimensions: inches (mm) 8 MAX. . (c) 2005 Microchip Technology Inc. DS21656C-page 11 TC1025 NOTES: DS21656C-page 12 (c) 2005 Microchip Technology Inc. TC1025 Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. 3. Your local Microchip sales office The Microchip Corporate Literature Center U.S. FAX: (480) 792-7277 The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products. (c) 2005 Microchip Technology Inc. DS21656C-page13 TC1025 NOTES: DS21656C-page14 (c) 2005 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * * Microchip products meet the specification contained in their particular Microchip Data Sheet. Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. Microchip is willing to work with the customer who is concerned about the integrity of their code. Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." * * * Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip's products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, Accuron, dsPIC, KEELOQ, microID, MPLAB, PIC, PICmicro, PICSTART, PRO MATE, PowerSmart, rfPIC, and SmartShunt are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. AmpLab, FilterLab, Migratable Memory, MXDEV, MXLAB, PICMASTER, SEEVAL, SmartSensor and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, dsPICDEM, dsPICDEM.net, dsPICworks, ECAN, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, Linear Active Thermistor, MPASM, MPLIB, MPLINK, MPSIM, PICkit, PICDEM, PICDEM.net, PICLAB, PICtail, PowerCal, PowerInfo, PowerMate, PowerTool, rfLAB, rfPICDEM, Select Mode, Smart Serial, SmartTel, Total Endurance and WiperLock are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2005, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona and Mountain View, California in October 2003. The Company's quality system processes and procedures are for its PICmicro(R) 8-bit MCUs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. (c) 2005 Microchip Technology Inc. DS21656C-page 15 WORLDWIDE SALES AND SERVICE AMERICAS Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Atlanta Alpharetta, GA Tel: 770-640-0034 Fax: 770-640-0307 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 San Jose Mountain View, CA Tel: 650-215-1444 Fax: 650-961-0286 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 ASIA/PACIFIC Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8676-6200 Fax: 86-28-8676-6599 China - Fuzhou Tel: 86-591-8750-3506 Fax: 86-591-8750-3521 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 China - Shunde Tel: 86-757-2839-5507 Fax: 86-757-2839-5571 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 China - Xian Tel: 86-29-8833-7250 Fax: 86-29-8833-7256 ASIA/PACIFIC India - Bangalore Tel: 91-80-2229-0061 Fax: 91-80-2229-0062 India - New Delhi Tel: 91-11-5160-8631 Fax: 91-11-5160-8632 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Korea - Gumi Tel: 82-54-473-4301 Fax: 82-54-473-4302 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Malaysia - Penang Tel: 60-4-646-8870 Fax: 60-4-646-5086 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-572-9526 Fax: 886-3-572-6459 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 EUROPE Austria - Wels Tel: 43-7242-2244-399 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 10/31/05 DS21656C-page 16 (c) 2005 Microchip Technology Inc. |
Price & Availability of TC1025CEOA
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |